Skip to content

5 Ways to Destroy Your Western Blot

Posted in: Protein Expression and Analysis
5 Ways to Destroy Your Western Blot

Western blotting is a common lab technique used to detect and analyze proteins. It also happens to be a really long and complicated procedure, with many steps along the way that are easy to mess up. How do you make sure that your Western blot is successful? Avoid the following five ways to destroy your Western blot:

[Edit: Now this is “4 ways to destroy your western blot!” – we had to retire the first one because it was inaccurate. Sorry about that!]

1. Neglect to fill empty lanes with buffer

Unlike an agarose gel, every lane of an SDS-PAGE gel needs to be filled to run properly. Once you’ve loaded all your samples and a molecular weight marker, fill the other wells with comparable volumes of loading buffer. Without this step, your bands will “smile”, turning up noticeably at the ends.

1. Lose track of the front/back, top/bottom; blot the wrong side of the membrane

It’s easy to lose track of where your proteins are on the gel once you’ve begun the transfer. My advice is to develop a rule of thumb that you always follow when removing gels from the gel box. For instance, I always slice a tiny amount of gel off the upper right hand corner of the gel. That way, even if the gel itself gets turned around, you can re-orient yourself.

Within the gel itself, the proteins are evenly distributed. On a membrane, however, the proteins will only be present on one side. Therefore, you also have to keep track of what side of the membrane the proteins are on. To keep the same orientation on the membrane as on your gel, you need to stack them carefully when setting up the transfer – lay the back of the gel on the front of the membrane. If you’re having trouble figuring it out, try to picture exactly how and where the proteins are moving when you apply charge. And don’t forget to mark which side of the membrane is the front when the transfer is complete!

2. Forget to include a ladder

A molecular weight marker needs to be included on every gel! And make sure you use a pre-stained ladder, or you’ll be helpless (ask me how I know this).

3. Get your antibodies wrong

Antibody problems are probably the most common cause for a failed Western blot – using the wrong concentration, using the wrong secondary, or using the wrong reporter. Antibody concentrations need to be optimized for both primary and secondary antibodies; check the literature, the manufacturer’s recommendations, and your lab mates’ experiences for what dilution you should be using. If the antibody is too dilute, you will need a very long exposure to see anything. If it is too concentrated, the signal will be so strong that it will be difficult to distinguish individuals bands. Next, double check that your secondary antibody recognizes the species of your primary antibody, i.e. if your primary is rabbit, the secondary should be anti-rabbit. Finally, make sure your secondary is conjugated to a reporter, such as HRP (hydrogen peroxide), otherwise you’ll just have a stack of antibodies with no way to detect them.

4. Over- or under- expose the blot

When it comes to imaging your blot, determining the exposure length can be somewhat of an art. Under-exposure of your blot will result in very faint bands, and over-exposure can result in an entirely black film. If you always use the same antibody at the same concentration, you probably have a good idea how long the blot needs to be imaged for. It’s a good idea to take a range of exposures, ranging from a few seconds to several minutes.

Have you found any different (perhaps even more creative) ways to destroy your western blot? Use the comments to tell us how.

Share this to your network:
Image Credit:


  1. sida on September 20, 2016 at 8:00 pm

    I was striping the dot blotted nitrocellulose membrane to probe with another antibody and I forgot to wash after stripping so I blocked the membrane directly. I’ll see the results now. 😐

  2. Joel on August 21, 2016 at 2:13 pm

    The author mentions always cutting a piece off the upper right hand corner of the gel to maintain orientation. My rule of thumb is that I know my ladder is always on the far left lane; I can always look at the ladder to orient myself.

    • Abdul-Karim Barakat on September 29, 2016 at 4:08 pm

      Well, always pipette the ladder on both edge lanes because it is not uncommon that the gel runs uneven. In this case you will need to cut a corner.

  3. GG on June 22, 2016 at 4:49 pm

    Okay, so I accidentally washed my blots after they had been blocking overnight. I know you’re supposed to go right to the addition of the primary antibody, but I absent mindedly washed the blots with TTBS 3x (5 min each). What does washing the blots after the blocking do? I just know I’m not supposed to, but I don’t want to mess up the results. Help is appreciated!

    • Af on July 7, 2016 at 12:58 pm

      Washing after blocking is perfectly fine.
      In fact, it is required in some labs.

  4. jennthegenius on October 19, 2012 at 9:40 pm

    Another way to destroy a WB: use the wrong buffer for transfer. Preferably one with a high salt concentration so that it boils, burns your membrane, and fuses the whole sandwich together <3

  5. Divya Goel on June 16, 2011 at 12:31 am

    Another way to destroy your western blot is by either not washing the membrane for enough time, so as to get fizzy results or washing it for longer times to get no results due to everything being washed off…So keep track of the washing times!!!:)

Leave a Comment

You must be logged in to post a comment.

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Scroll To Top